19618: cpu/stm32: fix riotboot settings for L4 and WB r=benpicco a=gschorcht
### Contribution description
This PR fixes the `riotboot` configuration for L4 and WB.
The family is not called `stm32l4` or `stm32wb` but `l4` and `wb`. That is, the `riotboot` configuration didn't work at all. Furthermore, a minimum `RIOTBOOT_LEN` of `0x2000` is required for L4.
Found when investigating the compilation errors for `bootloaders/riotboot_serial` in PR #19576.
### Testing procedure
1. Green CI.
2. Use the following commands:
```
BOARD=nucleo-l496zg make -C tests/riotboot info-debug-variable-RIOTBOOT_HDR_LEN
BOARD=p-nucleo-wb55 make -C tests/riotboot info-debug-variable-RIOTBOOT_HDR_LEN
```
In master these commands give
```
0x400
```
With this PR these commands give
```
0x200
```
as expected.
3. Use the following commands:
```
BOARD=nucleo-l496zg make -C tests/riotboot info-debug-variable-RIOTBOOT_LEN
BOARD=p-nucleo-wb55 make -C tests/riotboot info-debug-variable-RIOTBOOT_LEN
```
In master these commands give
```
0x1000
```
With this PR these commands give
```
0x2000
```
as expected.
### Issues/PRs references
19639: tests/net/gnrc_mac_timeout: add automated test r=aabadie a=aabadie
19644: gnrc_ipv6_nib: include RIO with all subnets in downstream RA r=benpicco a=benpicco
19649: gnrc_sixlowpan_iphc: prefix bits outside context must be zero r=benpicco a=benpicco
19656: gnrc/ipv6_auto_subnets: allow to configure minimal prefix length r=benpicco a=benpicco
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Co-authored-by: Alexandre Abadie <alexandre.abadie@inria.fr>
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
19335: ipv6/nib: 6LBR should not send RS on their downstream interface r=fabian18 a=fabian18
19581: cpu/samd5x: enable FDPLL1 at 200MHz r=benpicco a=dylad
### Contribution description
This PR allows to use the second FDPLL (the first one is used to generated the 120MHz frequency used by the core and some peripherals). The second FDPLL is setup to run at 200MHz which is the maximum allowed by this MCU.
In fact, I reused the existing function which setup FDPLL0 so it can be used in a generic way for both PLL (since they are the same IP).
I change the way the computation offset (left shift by 5) is done because 200MHz << 5 wouldn't fit inside an `uint32_t` and I wanted to avoid using an `uint64_t` here
Two additional commits are present for a small cleanup and a fix.
This is currently unused in our codebase, so it shouldn't impact this platform too much as the `ONDEMAND` bit is set. the FDPLL will not be running out of the box. But `@gschorcht` might need it pretty soon.
### Testing procedure
This PR can be tested on a `same54-xpro` and an oscilloscope using the following the patch:
```
From 76490845ec72387b24116bdd364a61365c186aa1 Mon Sep 17 00:00:00 2001
From: Dylan Laduranty <dylan.laduranty@mesotic.com>
Date: Thu, 11 May 2023 17:42:16 +0200
Subject: [PATCH] removeme! for debug purpose
Signed-off-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
---
cpu/samd5x/cpu.c | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
diff --git a/cpu/samd5x/cpu.c b/cpu/samd5x/cpu.c
index f778991a5b..2866c8c9e5 100644
--- a/cpu/samd5x/cpu.c
+++ b/cpu/samd5x/cpu.c
`@@` -220,7 +220,7 `@@` static void fdpll_init(uint8_t idx, uint32_t f_cpu)
}
static void gclk_connect(uint8_t id, uint8_t src, uint32_t flags) {
- GCLK->GENCTRL[id].reg = GCLK_GENCTRL_SRC(src) | GCLK_GENCTRL_GENEN | flags | GCLK_GENCTRL_IDC;
+ GCLK->GENCTRL[id].reg = GCLK_GENCTRL_SRC(src) | GCLK_GENCTRL_GENEN | flags | GCLK_GENCTRL_OE | GCLK_GENCTRL_IDC;
while (GCLK->SYNCBUSY.reg & GCLK_SYNCBUSY_GENCTRL(id)) {}
}
`@@` -384,6 +384,12 `@@` void cpu_init(void)
dma_init();
#endif
+ sam0_gclk_enable(SAM0_GCLK_200MHZ);
+ /* output both FDPLL (GCLK0 and GCLK4) to gpios */
+ gpio_init_mux(GPIO_PIN(PB, 14), GPIO_MUX_M);
+ gpio_init_mux(GPIO_PIN(PB, 10), GPIO_MUX_M);
+ /* PB14 -> EXT2 PB10 -> QSPI SCK */
+
/* initialize stdio prior to periph_init() to allow use of DEBUG() there */
early_init();
--
2.35.3
```
It will output both FDPLLs to PB14 and PB10. Their frequency can then be measured using an oscilloscope.
### Issues/PRs references
None.
19612: pkg/ndn-riot: drop unmaintained pkg r=benpicco a=maribu
### Contribution description
Upstream [1] has seen no activity since 2018, so it safe to assume this is dead. It is reasonable to assume that any users - if there ever were any - have moved on.
Fixes https://github.com/RIOT-OS/RIOT/issues/15638
[1]: https://github.com/named-data-iot/ndn-riot
19643: examples/suit_update: some test fixes r=aabadie a=kaspar030
19655: net/ipv6: make use of clz in ipv6_addr_match_prefix() r=benpicco a=benpicco
Co-authored-by: Fabian Hüßler <fabian.huessler@st.ovgu.de>
Co-authored-by: Dylan Laduranty <dylan.laduranty@mesotic.com>
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Co-authored-by: Kaspar Schleiser <kaspar@schleiser.de>
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
18477: gnrc_static: add static network configuration r=miri64 a=benpicco
19101: CI: update check-labels-action r=miri64 a=kaspar030
19155: Revert "sys/pm_layered: pm_(un)block add attribute optimize(3)" r=maribu a=Teufelchen1
Revert "sys/pm_layered: pm_(un)block add attribute optimize(3) -shortens hotpath"
This reverts commit 5447203921ab39962d7d378a631a6bc048e7f30b.
### Contribution description
Compiling `examples/gnrc_networking_mac` using `TOOLCHAIN=llvm` yields the following error:
```
RIOT/sys/pm_layered/pm.c:77:16: error: unknown attribute 'optimize' ignored [-Werror,-Wunknown-attributes]
__attribute__((optimize(3)))
```
As indicated, this is because the attribute `optimize` is GCC only and not present in LLVM.
Compare the manpages of [GCC](https://gcc.gnu.org/onlinedocs/gcc/Common-Function-Attributes.html) and [LLVM](https://clang.llvm.org/docs/AttributeReference.html).
### Testing procedure
Since this should only affect performance and not behavior, no special testing is needed. I am not aware of any tests in RIOT which could verify that assumption.
### Issues/PRs references
Introduced in #18846
There is another instance of this attribute being used in[ shell_lock.c](6fb340d654/sys/shell_lock/shell_lock.c (L80)). Since the usage is security related, I omit it from this PR.
Co-authored-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Co-authored-by: Kaspar Schleiser <kaspar@schleiser.de>
Co-authored-by: Teufelchen1 <bennet.blischke@haw-hamburg.de>
The macros CONCAT(), MIN(), and MAX() are defined over and over again in
RIOT's code base. This de-duplicates the code by moving the macros to a
common place.
- most were trivial
- missing group close or open
- extra space
- no doxygen comment
- name commad might open an implicit group
this hould also be implicit cosed but does not happen somtimes
- crazy: internal declared groups have to be closed internal
