We occasionally have some public `foo.h` header that includes a private
`foo_arch.h` header. Users are expected to include the `foo.h` header
and not the `foo_arch.h`. However, clangd will claim that the `#include`
of `foo.h` is unused if only functions / macros/ types / ... from
`foor_arch.h` is used and nothing from `foo.h`.
This adds the `IWYU pragma: export` comment to the include of
`foo_arch.h` in `foo.h`, so that clangd treats functions / macros /
types provided by `foo_arch.h` as if they were instead provided by
`foo.h`, which fixes the false positives.
This adds two functions:
void gpio_ll_switch_dir_output(gpio_port_t port, uword_t outputs);
void gpio_ll_switch_dir_input(gpio_port_t port, uword_t inputs);
The first configures GPIO pins specified by a bitmask as output, the
second configures the specified pins as input.
The main use case is to allow bit-banging bidirectional protocols using
more basic GPIO peripherals that do not implement open drain mode, such
as found e.g. on MSP430, ATmega, or SAM0.
It is not intended to implement this feature on modern MCUs with
sophisticated GPIO peripherals.
This adds the features
- periph_gpio_ll_input_pull_down:
To indicate support for input mode with internal pull down
- periph_gpio_ll_input_pull_keep:
To indicate support for input mode with internal resistor
pulling towards current level
- periph_gpio_ll_input_pull_up:
To indicate support for input mode with internal pull up
- periph_gpio_ll_disconnect:
To indicate a GPIO can be disconnected
- periph_gpio_ll_open_drain:
To indicate support for open drain mode
- periph_gpio_ll_open_drain_pull_up:
To indicate support for open drain mode with internal pull up
- periph_gpio_ll_open_source:
To indicate support for open source mode
- periph_gpio_ll_open_source_pull_down:
To indicate support for open source mode with internal pull down
The documentation on the state `GPIO_DISCONNECT` was a bit vague. The
API doc said it should disconnect the GPIO from all peripherals, the
test also tested them for being electrically disconnected.
The documentation in both the test and the API is extended to point out
that a GPIO indeed SHOULD be in high impedance state, but that user
MUST NOT expect that this requested is honored by every implementation
and for every GPIO pin.
In the test it is also pointed out that failing the test for a GPIO
in the `GPIO_DISCONNECT` state being electrically disconnected is for
some pins expected, and that the test should be just run again with
different GPIOs. The test intentionally tests for a feature not provided
by every GPIO pin rather than warning on a failure: The effort to just
flash and run the test again with different GPIOs is relatively low, but
it does confirm correct behavior of the API.
This commit optimizes the `gpio_conf_t` type in the following
regards:
- The "base" `gpio_conf_t` is stripped from members that only some
platforms support, e.g. drive strength, slew rate, and disabling of
the Schmitt Trigger are no longer universally available but
platform-specific extensions
- The `gpio_conf_t` is now crammed into a bit-field that is 8 bit or
16 bit wide. This allows for storing lots of them e.g. in
`driver_foo_params_t` or `uart_conf_t` etc.
- A `union` of the `struct` with bit-field members and a `bits` is used
to allow accessing all bits in a simple C statement and to ensure
alignment for efficient handling of the type
Co-authored-by: Gunar Schorcht <gunar@schorcht.net>
Allow accessing supported timer frequencies with a dedicated API.
This API needs to be implemented per platform and is available with
the feature periph_timer_query_freqs.
- Rename all `arduino_pinmap.h` to `arduino_iomap.h`
- An empty `arduino_pinmap.h` that just includes `arduino_iomap.h`
is provided for backward compatibility
- Move all info from `arduino_board.h` into the new file as trivial
macros, so that they can also be used outside of sketches
- The new name reflects the fact not just pin mappings, but also
other I/O features such as PWMs are mapped
- Drop all `arduino_board.h`
- `arduino_board.h` and `arduino_iomap.h` now provide the exact
same information, just in a different format
- a generic `arduino_board.h` is provided instead that just
uses the info in `arduinio_iomap.h` and provides them in the
format the code in `sys/arduino` expects it
- Add fine grained features to indicate for mappings
- availability of mappings for analog pins, DAC pins, PWM pins,
UART devices, SPI/I2C buses to the corresponding RIOT
identification can now be expressed:
- `arduino_pins`: `ARDUINO_PIN_0` etc. are available
- `arduino_analog`: `ARDUINO_A0` etc. are available
- `arduino_pwm`: `ARDUINO_PIN_13_PWM_DEV` etc. are available
- `arduino_dac`: `ARDUINO_DAC0` etc. are available
- `arduino_uart`: `ARDUINO_UART_D0D1` or similar are available
- `arduino_spi`: `ARDUINO_SPI_ISP` or similar are available
- `arduino_i2c`: `ARDUINO_I2C_UNO` or similar are available
- mechanical/electrical compatibility with specific form factors
can now be expressed as features:
- `aruino_shield_nano`: Arduino NANO compatible headers
- `aruino_shield_uno`: Arduino UNO compatible headers
- `aruino_shield_mega`: Arduino MEGA compatible headers
- `aruino_shield_isp`: ISP header is available
This provides the groundwork to implement shield support as modules
that can rely on the I/O mappings, rather than having to provide a
configuration per board.
19610: drivers/periph/rtc: improve doc on rtc_set_alarm r=maribu a=maribu
### Contribution description
- point out behavior on denormalized time stamps
- use errno codes to indicate errors (and adapt the few instances of actual error handling to use them)
19670: cpu/stm32: stm32f4 BRR from BSRR r=maribu a=kfessel
### Contribution description
sometimes one wants to save one instruction :)
just write the bits we need to write.
### Testing procedure
tests/periph/gpio_ll tests this
### Issues/PRs references
`@maribu` might know some reference
maybe #19407
19678: gnrc_sixlowpan_iphc: fix NULL pointer dereference r=maribu a=miri64
19679: gnrc_sixlowpan_frag_sfr: fix ARQ scheduler race-condition r=maribu a=miri64
19680: gnrc_sixlowpan_frag_rb: fix OOB write in _rbuf_add r=maribu a=miri64
19681: sys/xtimer: improve documentation r=maribu a=maribu
### Contribution description
- Add a warning that xtimer is deprecated, so that new code hopefully starts using ztimer
- Add a hint that `ztimer_xtimer_compat` can be used even after `xtimer` is gone
Co-authored-by: Marian Buschsieweke <marian.buschsieweke@ovgu.de>
Co-authored-by: Karl Fessel <karl.fessel@ovgu.de>
Co-authored-by: Martine Lenders <m.lenders@fu-berlin.de>
- point out behavior on denormalized time stamps
- use errno codes to indicate errors (and adapt the few instances of
actual error handling to use them)
The address in the USB device can be set either directly after the SETUP stage on receipt of the `SET ADDRESS Request` or after the associated status stage. When the USB device address has to be set depends on the hardware. If `USBDEV_SET_ADDR_AFTER_STATUS` has the value 1 (default), the address is only set in the USB device after the status stage. Overwrite it with 0 in `periph_cpu.h` to set the address already directly after the SETUP stage.
This commit adds dedicated stall functions for usbdev peripherals. Two
functions are added. The first function (usbdev_ep_stall) to enable and
disable the stall condition on generic endpoints. The second function is
a dedicated function to set the stall condition on endpoint zero in both
directions. This status can only be set and should automatically be
cleared by the usbdev implementation (or hardware) after a new setup
request is received from the host.
This is a temporary fix for Issue #17060. It allows to disable
auto inclusion of `ztimer_periph_rtt` in cases where another
module or application requires direct access.
Limitations:
- as ifeq are involved order of inclusion matters, therefore
these modules should be included early in the build at application
level and not in modules `Makefile.dep`
- this does not disallow direct inclusions of `ztimer_periph_rtt`,
since this only disables auto inclusion of these modules
This is a temporary solution since this is already possible with
Kconfig, but not in make.
