mirror of
https://github.com/RIOT-OS/RIOT.git
synced 2025-12-17 10:33:49 +01:00
126 lines
4.1 KiB
C
126 lines
4.1 KiB
C
/*
|
|
* Copyright 2015 Ludwig Knüpfer,
|
|
* 2015 Christian Mehlis
|
|
* 2016-2017 Freie Universität Berlin
|
|
*
|
|
* This file is subject to the terms and conditions of the GNU Lesser
|
|
* General Public License v2.1. See the file LICENSE in the top level
|
|
* directory for more details.
|
|
*/
|
|
|
|
#pragma once
|
|
|
|
/**
|
|
* @defgroup drivers_dht DHT Family of Humidity and Temperature Sensors
|
|
* @ingroup drivers_sensors
|
|
* @ingroup drivers_saul
|
|
* @brief Device driver for the DHT Family of humidity
|
|
* and temperature sensors
|
|
*
|
|
* This driver provides @ref drivers_saul capabilities.
|
|
*
|
|
* @{
|
|
*
|
|
* @file
|
|
* @brief Device driver interface for the DHT family of humidity
|
|
* and temperature sensors
|
|
*
|
|
* @author Ludwig Knüpfer <ludwig.knuepfer@fu-berlin.de
|
|
* @author Christian Mehlis <mehlis@inf.fu-berlin.de>
|
|
* @author Hauke Petersen <hauke.petersen@fu-berlin.de>
|
|
*/
|
|
|
|
#include <errno.h>
|
|
#include <stdint.h>
|
|
|
|
#include "periph/gpio.h"
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif
|
|
|
|
/**
|
|
* @brief Data type for storing DHT sensor readings
|
|
*/
|
|
typedef struct {
|
|
uint16_t humidity; /**< relative humidity in deci-percent */
|
|
uint16_t temperature; /**< temperature in deci-Celsius */
|
|
} dht_data_t;
|
|
|
|
/**
|
|
* @brief Device type of the DHT device
|
|
*/
|
|
typedef enum {
|
|
DHT11, /**< Older DHT11 variants with either 1 °C or
|
|
* 0.1 °C resolution */
|
|
DHT11_2022, /**< New DHT11 variant with 0.01 °C resolution */
|
|
DHT22, /**< DHT22 device identifier */
|
|
DHT21 = DHT22, /**< DHT21 device identifier */
|
|
AM2301 = DHT22, /**< AM2301 device identifier */
|
|
} dht_type_t;
|
|
|
|
/**
|
|
* @brief Configuration parameters for DHT devices
|
|
*/
|
|
typedef struct {
|
|
gpio_t pin; /**< GPIO pin of the device's data pin */
|
|
dht_type_t type; /**< type of the DHT device */
|
|
gpio_mode_t in_mode; /**< input pin configuration, with or without pull
|
|
* resistor */
|
|
} dht_params_t;
|
|
|
|
/**
|
|
* @brief Device descriptor for DHT sensor devices
|
|
*/
|
|
typedef struct {
|
|
dht_params_t params; /**< Device parameters */
|
|
dht_data_t last_val; /**< Values of the last measurement */
|
|
} dht_t;
|
|
|
|
/**
|
|
* @brief Initialize a new DHT device
|
|
*
|
|
* @param[out] dev device descriptor of a DHT device
|
|
* @param[in] params configuration parameters
|
|
*
|
|
* @retval 0 Success
|
|
* @retval -EXDEV A low level on the input after the sensor's startup
|
|
* time indicates that either no sensor or pull-up
|
|
* resistor is connected, or the sensor is physically
|
|
* poorly connected or powered.
|
|
* @retval -ENODEV The sensor did not respond to the transmission of a
|
|
* start signal. Likely there were a pull-up resistor but
|
|
* no sensor connected on the data line.
|
|
*/
|
|
int dht_init(dht_t *dev, const dht_params_t *params);
|
|
|
|
/**
|
|
* @brief get a new temperature and/or humidity value from the device
|
|
*
|
|
* @note if reading fails or checksum is invalid, no new values will be
|
|
* written into the result values
|
|
*
|
|
* @param[in] dev device descriptor of a DHT device
|
|
* @param[out] temp temperature value [in °C * 10^-1],
|
|
* may be NULL if not needed
|
|
* @param[out] hum relative humidity value [in percent * 10^-1],
|
|
* may be NULL if not needed
|
|
*
|
|
* @retval 0 Success
|
|
* @retval -ENODEV The sensor did not respond to the transmission of a
|
|
* start signal. Likely the RESPAWN_TIMEOUT is
|
|
* insufficient.
|
|
* @retval -EIO The received and the expected checksum didn't match.
|
|
* @retval -ENOSYS Unable to parse the received data. Likely the data
|
|
* format is not implemented.
|
|
* @retval -ERANGE Temperature low byte >= 10. Likely misconfigured
|
|
* device type (DHT11_2022).
|
|
*/
|
|
int dht_read(dht_t *dev, int16_t *temp, int16_t *hum);
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
/** @} */
|