Merge pull request #13395 from smlng/pr_doc_phynode
boards: update doc of phyNode (pba-d-01-kw2x)
This commit is contained in:
MichelRottleuthner
GitHub
commit
098c3ef3e1
@ -9,17 +9,15 @@ Designed and produced by PHYTEC Messtechnik GmbH, D-55129 Mainz.
|
||||
contact@phytec.de
|
||||
|
||||
## Overview
|
||||
The [Phytec IoT wiki](https://github.com/PHYTEC-Messtechnik-GmbH/phynode-riot-examples/wiki)
|
||||
describes the phyWAVE module and the phyNODE board more
|
||||
detailed. The links below will guide you directly to the corresponding chapter:
|
||||
* [Overview](https://github.com/PHYTEC-Messtechnik-GmbH/phynode-riot-examples/wiki/)
|
||||
* [Introduction](https://github.com/PHYTEC-Messtechnik-GmbH/phynode-riot-examples/wiki/Introduction)
|
||||
* Hardware descriptions for the
|
||||
[phyWAVE](https://github.com/PHYTEC-Messtechnik-GmbH/phynode-riot-examples/wiki/phyWAVE-KW2x-Characteristics)
|
||||
and the
|
||||
[phyNODE](https://github.com/PHYTEC-Messtechnik-GmbH/phynode-riot-examples/wiki/phyNODE-Characteristics)
|
||||
* [Toolchain, build and debug Information](https://github.com/PHYTEC-Messtechnik-GmbH/phynode-riot-examples/wiki/RIOT-getting-started#toolchain-summary)
|
||||
* [A detailed step-by-step Guide that explains how to set up the Environment](https://github.com/PHYTEC-Messtechnik-GmbH/phynode-riot-examples/wiki/RIOT-getting-started#step-by-step-installation-guide)
|
||||
|
||||
The phyNODE evaluation board consists of a [phyWAVE](https://www.phytec.de/produkte/internet-of-things/phywave/)
|
||||
module mounted on a common PCB with several sensor and actuator modules.
|
||||
The board provides 2 USB ports. The one next to the white imprint *cmsis-dap*
|
||||
is meant for development (debug and flash). The second one, next to the golden
|
||||
*PHYTEC* imprint, is connected to the USB peripheral of the MCU and may be used
|
||||
by a firmware (currently not supported).
|
||||
|
||||
|
||||
The implementation status of the phyWAVE and phyNODE peripherals are listed
|
||||
below. You can find links to the corresponding Pull Requests which may give you
|
||||
a code reference.
|
||||
@ -27,11 +25,44 @@ a code reference.
|
||||
<img src="https://raw.githubusercontent.com/jremmert-phytec-iot/Pictures_Phytec_IOT/master/EvalBoard_3.png" width="800" />
|
||||
phyNODE board with equipped phyWAVE-KW2x processor/radio-module.
|
||||
|
||||
### Details
|
||||
The PCB-pieces with the mounted sensors can be separated from the evaluation
|
||||
board to capture sensor values from specific spatial points.
|
||||
@note The PCB-pieces with the mounted sensors can be separated from the
|
||||
evaluation board to capture sensor values from specific spatial points.
|
||||
|
||||
[Pinout reference](https://github.com/PHYTEC-Messtechnik-GmbH/phynode-riot-examples/wiki/Interfaces)
|
||||
## Pinout Reference
|
||||
|
||||
The board features an Arduino like header connector to mount shields. The
|
||||
spacing of the 4 pin rows is a bit offset, thus shields might not fit perfectly.
|
||||
|
||||
The pinout below shows the vendor specific naming and functionality.
|
||||
The actual pin configuration of the board for RIOT can be found in
|
||||
[periph_conf.h](https://github.com/RIOT-OS/RIOT/blob/master/boards/pba-d-01-kw2x/include/periph_conf.h).
|
||||
|
||||
@note Not all signals and pins are compatible with Arduino Uno R3.
|
||||
|
||||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||||
_X1____________________
|
||||
| D15 |___DIO21, PE19, I2C0 SCL
|
||||
| D14 |___DIO20, PE18, I2C0 SDA
|
||||
| AREF |___AREF, VCC3V3
|
||||
| GND3 |___GND
|
||||
X___| RESERVED D13 |___DIO3, PC5, SPI0 SCK
|
||||
VCC3V3___| IOREF D12 |___DIO5, PC7, SPI0 MISO
|
||||
nRESET___| RST TGTMCU D11 |___DIO4, PC6, SPI0 MOSI
|
||||
VCC3V3___| P3V3 D10 |___DIO2, PC4, SPI0 CS0
|
||||
P5V USB OUT___| P5V USB D9 |___DIO9, PD4, PWM
|
||||
GND_________| GND2 D8 |___DIO6, PD1
|
||||
\___| GND1 |
|
||||
X___| P5_9V VIN D7 |___DIO24, PA1, PWM, TDI2
|
||||
| D6 |___DIO25, PA2, PWM, TDO2
|
||||
DIO15, PE2, ADC ___| A0 D5 |___DIO11, PD6, PWM
|
||||
DIO16, PE3, ADC, TDO1 ___| A1 D4 |___DIO29, PA19, TCLKIN
|
||||
DIO12, PD7, ADC ___| A2 D3 |___DIO27, PA4, PWM
|
||||
DIO10, PD5, ADC ___| A3 D2 |___DIO17, PE4, LLWU, TDI1
|
||||
DIO13, PE0, ADC, I2CSDA ___| A4 D1 |___DIO8, PD3, UART2 TX
|
||||
DIO14, PE1, ADC, I2CSCL ___| A5 D0 |___DIO7, PD2, UART2 RX
|
||||
-----------------------
|
||||
Arduino Uno R3 Connector
|
||||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
|
||||
|
||||
## Implementation Status
|
||||
|
||||
@ -55,5 +86,5 @@ board to capture sensor values from specific spatial points.
|
||||
| Magnetometer | [MAG3110FCR1](http://www.nxp.com/products/sensors/magnetometers/sample-data-sets-for-inertial-and-magnetic-sensors/freescale-high-accuracy-3d-magnetometer:MAG3110) | yes | [mainline](https://github.com/RIOT-OS/RIOT/pull/2121) |
|
||||
| Light Sensor | [TCS3772](https://ams.com/jpn/content/download/291143/1065677/file/TCS3772_Datasheet_EN_v1.pdf) | yes | [mainline](https://github.com/RIOT-OS/RIOT/pull/3135) |
|
||||
| IR-Termopile Sensor | [TMP006](http://www.ti.com/product/TMP006) |yes | [mainline](https://github.com/RIOT-OS/RIOT/pull/2148) |
|
||||
| Capacitive Button | PCB | no | planned |
|
||||
| Capacitive Button | PCB | yes | [mainline](https://github.com/RIOT-OS/RIOT/pull/7147) |
|
||||
*/
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user