From 7cfabf0142c67e48bd0929b48271bcc38a9a7d40 Mon Sep 17 00:00:00 2001 From: Marian Buschsieweke Date: Thu, 4 Jun 2020 11:08:48 +0200 Subject: [PATCH] boards/mulle: Fix units & alignment in doc --- boards/mulle/doc.txt | 50 ++++++++++++++++++++++---------------------- 1 file changed, 25 insertions(+), 25 deletions(-) diff --git a/boards/mulle/doc.txt b/boards/mulle/doc.txt index e0d97ee025..8bc005b862 100644 --- a/boards/mulle/doc.txt +++ b/boards/mulle/doc.txt @@ -21,14 +21,14 @@ Use `BOARD=mulle` for building RIOT for this platform. https://github.com/eistec/mulle/wiki/Datasheets contains a list of relevant documentation for the components. -| MCU | MK60DN512VLL10 – Cortex-M4 | -|-------|-----------------------------------| -| RAM | 64kB | -| Flash | 512kB| -| radio chipset | AT86RF212B, sub-GHz IEEE802.15.4 transceiver, similar to the AT86RF233 | -| external flash memory | Micron M25P16 16 Mbits external NOR flash, used for storing configuration, measurements and other slow changing non-volatile data | -| external FRAM memory | Cypress/Ramtron FM25L04B 4 Kbits external F-RAM, used for storing counters and other rapidly changing non-volatile data | -| accelerometer | ST micro LIS3DH MEMS accelerometer, | +| MCU | MK60DN512VLL10 – Cortex-M4 | +|:--------------------- |:--------------------------------------------------------------------------------------------------------------------------------- | +| RAM | 64KiB | +| Flash | 512KiB | +| radio chipset | AT86RF212B, sub-GHz IEEE802.15.4 transceiver, similar to the AT86RF233 | +| external flash memory | Micron M25P16 2 MiB external NOR flash, used for storing configuration, measurements and other slow changing non-volatile data | +| external FRAM memory | Cypress/Ramtron FM25L04B 512B external F-RAM, used for storing counters and other rapidly changing non-volatile data | +| accelerometer | ST micro LIS3DH MEMS accelerometer | ## Layout @@ -40,23 +40,23 @@ documentation for the components. The Mulle board is supported by mainline RIOT. See the below table for software support status for the different components. -| Device | ID | Supported | Comments | -|:------------- |:------------- |:------------- |:------------- | -| MCU | MK60DN512VLL10 | partly | See below | -| Low-level driver | GPIO | yes | | -| | PWM | yes | | -| | UART | yes | | -| | I2C | yes | | -| | SPI | yes |Master mode works, slave mode unsupported | -| | USB | no | [PR#3890](https://github.com/RIOT-OS/RIOT/pull/3890) | -| | RTT | yes | | -| | RNG | yes | | -| | timer | yes | uses LPTMR module for TIMER_0 (used by xtimer), 32.768 kHz tick rate. PIT for additional timers, F_BUS tick rate (48 MHz default) | -| | PM/LLWU | in progress | [PR#2605](https://github.com/RIOT-OS/RIOT/pull/2605) | -| Radio Chip | AT86RF212B | yes | | -| Accelerometer | LIS3DH | yes | | -| Flash | M25P16 | in progress | [PR#6762](https://github.com/RIOT-OS/RIOT/pull/6762) | -| FRAM | FM25L04B | yes | | +| Device | ID | Supported | Comments | +|:----------------- |:----------------- |:------------- |:----------------------------------------------------- | +| MCU | MK60DN512VLL10 | partly | See below | +| Low-level driver | GPIO | yes | | +| | PWM | yes | | +| | UART | yes | | +| | I2C | yes | | +| | SPI | yes | Slave mode unsupported | +| | USB | no | [PR#3890](https://github.com/RIOT-OS/RIOT/pull/3890) | +| | RTT | yes | | +| | RNG | yes | | +| | timer | yes | uses LPTMR module for TIMER_0 (used by xtimer), 32.768 kHz tick rate. PIT for additional timers, F_BUS tick rate (48 MHz default) | +| | PM/LLWU | in progress | [PR#2605](https://github.com/RIOT-OS/RIOT/pull/2605) | +| Radio Chip | AT86RF212B | yes | | +| Accelerometer | LIS3DH | yes | | +| Flash | M25P16 | yes | | +| FRAM | FM25L04B | yes | | ## Toolchains