The stm32mp1 family has no flash. The firmware is loaded directly in
RAM by stlink programmer or by Cortex-A7 bootloader/OS.
Thus bootloader is useless for this family, disable it.
Signed-off-by: Gilles DOFFE <gilles.doffe@savoirfairelinux.com>
As stm32mp1 family accesses gpio pins with a different
offset than other stm32, create a specific macro.
Signed-off-by: Gilles DOFFE <gilles.doffe@savoirfairelinux.com>
clk_conf is a useful tool to produce clock headers for new boards.
But it only supports STM32Fx families.
This commits add the definition of a new family: STM32MP1.
Only the STM32MP157 is supported for now.
First build clk_conf:
$ make -C cpu/stm32/dist/clk_conf/
Clock header can be generated with the following command once clk_conf is
built:
$ cpu/stm32/dist/clk_conf/clk_conf stm32mp157 208000000 24000000 1
This command line will produce a core clock of 208MHz with a 24MHz HSE
oscillator and will use LSE clock which corresponds to the STM32MP157C-DK2
board configuration.
The command will output the header to copy paste into the periph_conf.h of
the board:
/**
* @name Clock settings
*
* @note This is auto-generated from
* `cpu/stm32/dist/clk_conf/clk_conf.c`
* @{
*/
/* give the target core clock (HCLK) frequency [in Hz],
* maximum: 209MHz */
#define CLOCK_CORECLOCK (208000000U)
/* 0: no external high speed crystal available
* else: actual crystal frequency [in Hz] */
#define CLOCK_HSE (24000000U)
/* 0: no external low speed crystal available,
* 1: external crystal available (always 32.768kHz) */
#define CLOCK_LSE (1U)
/* peripheral clock setup */
#define CLOCK_MCU_DIV RCC_MCUDIVR_MCUDIV_1 /* max 209MHz */
#define CLOCK_MCU (CLOCK_CORECLOCK / 1)
#define CLOCK_APB1_DIV RCC_APB1DIVR_APB1DIV_2 /* max 104MHz */
#define CLOCK_APB1 (CLOCK_CORECLOCK / 2)
#define CLOCK_APB2_DIV RCC_APB2DIVR_APB2DIV_2 /* max 104MHz */
#define CLOCK_APB2 (CLOCK_CORECLOCK / 2)
#define CLOCK_APB3_DIV RCC_APB3DIVR_APB3DIV_2 /* max 104MHz */
#define CLOCK_APB3 (CLOCK_CORECLOCK / 2)
/* Main PLL factors */
#define CLOCK_PLL_M (2)
#define CLOCK_PLL_N (52)
#define CLOCK_PLL_P (3)
#define CLOCK_PLL_Q (13)
/** @} */
This result has been verified with STM32CubeMX, the official ST tool.
Signed-off-by: Gilles DOFFE <gilles.doffe@savoirfairelinux.com>
APB1 bus clock is always enabled is not manageable by RCC register.
So avoid enabling it.
Signed-off-by: Gilles DOFFE <gilles.doffe@savoirfairelinux.com>
* Setup i2c speed to I2C_SPEED_LOW by default
* enable i2c_write_regs() function.
* i2c frequency needs to be specified into board periph_conf.h
Signed-off-by: Gilles DOFFE <gilles.doffe@savoirfairelinux.com>
In some CMSIS headers, "typedef enum" could be preceded by white
spaces. Thus consider them when parsing the line.
Signed-off-by: Gilles DOFFE <gilles.doffe@savoirfairelinux.com>
Default values were wrong for WB when using HSE 32MHz as PLL input source
Default PLL input source was wrong when not using HSE and the board
provides an HSE
By using the RTC helper functions instead of POSIX mktime()/gmtime()
we can not only extend the RTC range beyond Y2038.
For tests/periph_rtc:
before:
text data bss dec hex filename
28028 248 2472 30748 781c stk3700/tests_periph_rtc.elf
after:
text data bss dec hex filename
19400 144 2424 21968 55d0 stk3700/tests_periph_rtc.elf
fixes#13277
irq_arch.h previously included cpu.h, which in term included the vendor header
files. Those were needed to get the GIE define (general interrupt enable bit).
However, the vendor files use fancy defines like `#define N (0x0004)` that
easily conflict with application code. Due to the widespread use of the IRQ API,
it is better to not include the vendor files in irq_arch.h.
This commit adds a local define for the GIE bit and uses this instead of
including cpu.h.
